Skip to main content

Drivers 5.1.0 · Device profiles 9.1.0

Published on 2026-09-18.

Breaking changes​

An integration reading these points may need to be adapted.

Point fields that change​

DriverWhat changes
nexelec:x2:1Formaldehyde moves from ch2o to ch2oLevel (unit ppb unchanged): on ratio units the ontology field now carries the Level suffix.
adeunis:motion:2Luminosity moves from illuminance in lx to luminosityLevel in %, and the presence counter to occupancyLevel, as the Motion codec specifies.
arad:sonata:1The battery reading moves from batteryLevel in % to batteryVoltage in V: the device reports a voltage (3.294), never a percentage.
dezem:harvy2:1Input 4 and the sum of inputs 1 to 4 both wrote current:4. Input 4 keeps current:4, the sum moves to current:5. Readings equal to 0 are published instead of being dropped.
elsys:generic:1Occupancy and motion counters both wrote counter, so one overwrote the other. Occupancy keeps counter, motion moves to counter:6.
yobiiq:em4301:1The current and voltage transformer ratios are no longer published as current and voltage: they are configuration, not measurements. The four active energies are published instead.
glbsat:th:1Carbon monoxide moves from co to coLevel (unit ppm unchanged).
inbiot:inbiot-decoder:1TVOC, formaldehyde, ozone, nitrogen dioxide and carbon monoxide move from tvoc, ch2o, o3, no2 and co to tvocLevel, ch2oLevel, o3Level, no2Level and coLevel (units ppb/ppm unchanged).
lbearth:generic:1The main battery moves from batteryLevel in % to batteryVoltage:1 in mV: the device reports millivolts. The 9 V battery keeps batteryVoltage.
jri:lora-spy-th1:1The second redundancy set was inverted: its temperature was published as humidity:1 and its humidity as temperature:3. The two tracks are now on the right fields.
tektelic:t0008781-stork:1batteryLevel now carries the remaining battery capacity instead of the core tick count.
watteco:ticso:4The energy indexes move from powerRate in W/h to energy in Wh: they are energies, not rates. Values unchanged.
watteco:ticso:5The energy indexes move from powerRate in W/h to energy in Wh: they are energies, not rates. Values unchanged.
watteco:triphaso:4The active energies move from powerRate:1…powerRate:8 in W/h to energy:1…energy:8 in Wh. Values unchanged. Three example points whose index no longer matched the driver are realigned (rmsVoltage:1, current:1 and angle:1 of the phase B frame become :2).
asystom:sentinel-bmk1:1The rotation speeds move from vibration:1…vibration:3 in mgravity to angularVelocity:1…angularVelocity:3 in rpm: the decoder reports revolutions per minute.
watteco:smart-plug:4The active energy moves from powerRate in W/h to energy in Wh. Value unchanged.
watteco:smart-plug:5The active energy moves from powerRate in W/h to energy in Wh. Value unchanged.
watteco:triphaso:5The active energies move from powerRate:1…powerRate:8 in W/h to energy:1…energy:8 in Wh. Values unchanged.

Point units and values that change​

DriverWhat changes
dl:dl-iam:1The pressure was decoded in pascals but published as hPa: the value is now divided by 100.
dl:dl-kl66:1The weight was decoded in grams but published as kg: the value is now divided by 1000.
dl:dl-pr36ctd:1The pressure was decoded in bar but published as hPa: the value is now multiplied by 1000.
dl:dl-trs12:1The conductivity was decoded in µS/cm but published as S/m: the value is now converted (×1e-4).
sensaio:generic:1Temperatures were decoded in kelvin but published as Cel, and the pressure in pascals as hPa: the values are now converted (−273.15 and ÷100). A 295.2 reading becomes 22.05 °C.
tektelic:agro:1The moisture index was stacked into the frequency point, which mixed 1362 Hz and 0.8 in one series. frequency now carries the frequency alone; the moisture index is not published until its unit is confirmed.
thrmkn:generic:1The battery voltage was published as V while the device reports millivolts: it is now mV with the raw value (1560 mV), which is also what the BACnet mapping declares.
axioma:w1:1The volumes were decoded in litres but published as m3: the values are now divided by 1000.

Drivers​

abeeway​

DriverChangeWhat changed
abeeway:asset-tracker-3:1updatedNew points: status Motion (state), accuracy (m), speed (m/s), angle Heading (deg), batteryVoltage (mV), temperature Current (Cel), percentage Motion (%), counter Shocks (count), and 2 more
abeeway:asset-tracker:2updatedNew points: status Motion (state), temperature Maximum (Cel), angle Heading (deg), batteryVoltage Measures (V), counter Activity (count)

adeunis​

DriverChangeWhat changed
adeunis:breath:1updatedNew points: status Digital input 1 (state), counter Digital input 1 (count), status Digital input 2 (state), counter Digital input 2 (count)
adeunis:comfort-co2:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:comfort-serenity:1updatedNew points: index VOC (Minimum) (index), index VOC (Maximum) (index), index VOC (Average) (index), index VOC (index)
adeunis:comfort:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:comfort:2updatedNew points: temperature Alarm active (Cel), humidity Alarm inactive (%RH), status Digital input 1 (state), counter Digital input 1 (count), status Digital input 2 (state), counter Digital input 2 (count)
adeunis:delta-p:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:dry-contacts:2updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:motion:1updatedNew points: luminosityLevel (%), counter Presence (count)
adeunis:motion:2updatedNew points: occupancyLevel (%), luminosityLevel (%), presence (state), status Presence alarm (state)
adeunis:pulse:2updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:pulse:3updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:pulse4:1updatedNew points: leak Channel A (state), leak Channel B (state), counter Channel A (count), counter Channel B (count), counter
adeunis:temp:3updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
adeunis:temp4:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

advantech​

DriverChangeWhat changed
advantec:wise:1updatedNew points: velocity Overall (X axis) (mm/s), acceleration Peak (X axis) (mgravity), acceleration RMS (X axis) (mgravity), ratio Kurtosis (X axis) (/), ratio Crest factor (X axis) (/), distance Peak-to-peak displacement (X axis) (um), velocity Overall (Y axis) (mm/s), acceleration Peak (Y axis) (mgravity), and 10 more

arad​

DriverChangeWhat changed
arad:sonata:1updatedNew points: leak (state), status Burst pipe (state)

ascoel​

DriverChangeWhat changed
ascoel:cm:1updatedNew points: counter (count)
ascoel:ir:1updatedNew points: counter (count)
ascoel:pb:1updatedNew points: counter (count)

asystom​

DriverChangeWhat changed
asystom:sentinel-bmk1:1updatedRotation speeds in RPM were published as acceleration in mgravity: now angularVelocity in rpm

atim​

DriverChangeWhat changed
atim:generic:1updatedNew points: humidity Channel 1 (%RH), status

axioma​

DriverChangeWhat changed
axioma:w1:1updatedVolumes were decoded in litres but published in m3: values divided by 1000, unit unchanged

b-meters​

DriverChangeWhat changed
b-meters:hydrodigit:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
b-meters:iwm-lr5:1addedB Meters IWM-LR5 codec: standard, compact, extended, datalogger, JSON and alarm uplinks, 12 downlink commands

cisco​

DriverChangeWhat changed
cisco:av-nv:1updatedNew points: status Contact (state), presence (state), pm1 (ug/m3), pm2_5 (ug/m3), pm10 (ug/m3), density Particles > 0.3 um (#/cm3), density Particles > 0.5 um (#/cm3), density Particles > 1.0 um (#/cm3), and 30 more

citylone​

DriverChangeWhat changed
citylone:generic:1updatedNew points: status Dry contact 1 (state), status Dry contact 2 (state), duration Lamp11 (h), duration Lamp12 (h), duration Lamp21 (h), duration Lamp22 (h), duration Lamp 1-10V (h), duration Relay (h)

decentlab​

DriverChangeWhat changed
dl:dl-5tm:1updatedNew points: temperature (Cel)
dl:dl-atm22:1updatedNew points: speed Wind (m/s), speed Wind (Maximum) (m/s), angle Wind direction (deg), angle Tilt (X axis) (deg), angle Tilt (Y axis) (deg)
dl:dl-atm41:1updatedNew points: speed Wind (m/s), speed Wind (Maximum) (m/s), angle Wind direction (deg), angle Tilt (X axis) (deg), angle Tilt (Y axis) (deg), solarRadiation (W/m2), height (mm), counter (count), and 4 more
dl:dl-atm41g2:1addedDecentLab DL-ATM41G2 weather station (2nd generation) driver
dl:dl-blg:1addedDecentLab DL-BLG driver
dl:dl-ctd10:1updatedNew points: height (mm), conductivity (uS/cm), status Freezing (state)
dl:dl-ctd10b:1addedDecentLab DL-CTD10B driver
dl:dl-cws:1addedDecentLab DL-CWS driver
dl:dl-cws2:1addedDecentLab DL-CWS2 driver
dl:dl-dlr2-011:1addedDecentLab DL-DLR2-011 driver: two dry-contact inputs and battery voltage
dl:dl-iam:1updatedNew points: tvocLevel (ppb), counter (count)
dl:dl-isf:1addedDecentLab DL-ISF driver
dl:dl-itst:1updatedNew points: temperature Target (Cel)
dl:dl-kl66:1updatedNew points: distance (um), strain (um/m)
dl:dl-lws:1addedDecentLab DL-LWS driver
dl:dl-mes5:1addedDecentLab DL-MES5 driver
dl:dl-ntu:1addedDecentLab DL-NTU driver
dl:dl-pheht:1addedDecentLab DL-PHEHT driver
dl:dl-pr36ctd:1updatedNew points: temperature (Cel)
dl:dl-sdd:1addedDecentLab DL-SDD driver
dl:dl-smtp:1updatedNew points: temperature Depth 0 (Cel), temperature Depth 1 (Cel), temperature Depth 2 (Cel), temperature Depth 3 (Cel), temperature Depth 4 (Cel), temperature Depth 5 (Cel)
dl:dl-tbrg:1updatedNew points: height Precipitation (mm), height Cumulative precipitation (mm)
dl:dl-trs11:1updatedNew points: temperature (Cel)
dl:dl-trs12:1updatedNew points: temperature (Cel)
dl:dl-trs21:1updatedNew points: pressure (kPa), temperature (Cel)

dezem​

DriverChangeWhat changed
dezem:harvy2:1updatedNew points: powerFactor (/)

dragino​

DriverChangeWhat changed
dragino:laq4:1addedDragino's own LAQ4 decoder (latest firmware) with ontology points
dragino:lht65:1addedDragino's own LHT65 decoder (latest firmware) with ontology points
dragino:llms01:1addedDragino's own LLMS01 decoder (latest firmware) with ontology points
dragino:lsn50-v2:1addedDragino's own LSN50-V2 decoder (latest firmware) with ontology points
dragino:lsn50v2-d20:1addedDragino's own LSN50V2-D20 decoder (latest firmware) with ontology points
dragino:lsph01:1addedDragino's own LSPH01 decoder (latest firmware) with ontology points
dragino:lt22222-l:1addedDragino's own LT22222-L decoder (latest firmware) with ontology points
dragino:ltc2:1addedDragino's own LTC2 decoder (latest firmware) with ontology points

eastron​

DriverChangeWhat changed
eastron:sdm230-lora-mid:1updatedNew points: powerFactor (/)
eastron:sdm630mct-lora:1updatedNew points: energy (kWh)

elsys​

DriverChangeWhat changed
elsys:generic:1updatedNew points: status Digital input 1 (state), counter Motion (count)

enginko​

DriverChangeWhat changed
enginko:level-sensors:1updatedNew points: status Digital input (state), status Digital output (state)

eolane​

DriverChangeWhat changed
eolane:bob:1updatedNew points: frequency Peak (hertz), percentage Anomaly (%)
eolane:movee:1updatedNew points: acceleration gz (mgravity)

ezurio​

DriverChangeWhat changed
ezurio:rs26x:1addedEzurio Sentrius RS26x manufacturer codec: temperature, backlog and aggregated uplinks, configuration downlinks

fludia​

DriverChangeWhat changed
fludia:fm432e:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
fludia:fm432g:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
fludia:fm432p:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

globalsat​

DriverChangeWhat changed
glbsat:th:1updatedNew points: coLevel (ppm)

gwf​

DriverChangeWhat changed
gwf:rcm-lrw10:1updatedNew points: leak (state), status Burst (state)

honeywell​

DriverChangeWhat changed
honey-w:HVT-R110-2:1updatedNew points: ratio Kurtosis (X axis) (/), ratio Kurtosis (Y axis) (/), ratio Kurtosis (Z axis) (/), ratio Crest factor (X axis) (/), ratio Crest factor (Y axis) (/), ratio Crest factor (Z axis) (/)
honey-w:HVT-R110:1updatedNew points: ratio Kurtosis (X axis) (/), ratio Kurtosis (Y axis) (/), ratio Kurtosis (Z axis) (/), ratio Crest factor (X axis) (/), ratio Crest factor (Y axis) (/), ratio Crest factor (Z axis) (/)

inbiot​

DriverChangeWhat changed
inbiot:inbiot-decoder:1updatedNew points: tvocLevel (ppb), index Air quality (index), index Ventilation (index), index Thermal comfort (index), ch2oLevel (ppb), o3Level (ppb), no2Level (ppb), coLevel (ppm)

iot-factory​

DriverChangeWhat changed
iot-fact:generic:1updatedNew points: counter, status, status Movement (state)
iot-fact:m-bus-gateway:1updatedNew points: energy (Wh)

jri​

DriverChangeWhat changed
jri:lora-spy-th1:1updatedNew points: status Open detection (state)

kamstrup​

DriverChangeWhat changed
kamstrup:generic:1updatedNew points: energy (Wh)

laird​

DriverChangeWhat changed
laird:ext-multi:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
laird:ext-temp-rtd:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

liebearth​

DriverChangeWhat changed
lbearth:generic:1updatedNew points: batteryVoltage 9V battery (mV)

lumel​

DriverChangeWhat changed
lumel:nr32:1updatedNew points: energy (kWh)

maddalena​

DriverChangeWhat changed
mdlna:arrowwan2:1updatedNew points: leak (state), volume

mclimate​

DriverChangeWhat changed
mclimate:fan-coil:1updatedNew points: status Valve (state)
mclimate:fan-coil:2updatedNew points: status Valve (state)
mclimate:open-close:1updatedNew points: status Open/close (state)
mclimate:open-close:2updatedNew points: status Open/close (state)
mclimate:t-valve:1updatedNew points: status Manual open (state)
mclimate:vicki:1updatedNew points: percentage (%)
mclimate:vicki:2updatedNew points: percentage (%)

merryiot​

DriverChangeWhat changed
merryiot:wl10:1updatedNew points: leak (state)

milesight-iot​

DriverChangeWhat changed
msight:am100-series:1updatedNew points: pressure (hPa)
msight:am104:1updatedNew points: counter PIR activity (count)
msight:am300-series:1updatedNew points: ch2o (mg/m3), pm2_5 (ug/m3), pm10 (ug/m3)
msight:am304l:1updatedNew points: batteryLevel (%), humidity (%RH), presence (state), counter PIR (count), illuminance (lx)
msight:am305l:1updatedNew points: batteryLevel (%), humidity (%RH), co2Level (ppm), illuminance (lx)
msight:ct303:2updatedNew points: current Channel 1 (Maximum) (A), current Channel 1 (Minimum) (A), charge Channel 1 (Ah)
msight:ct305:2updatedNew points: current Channel 1 (Maximum) (A), current Channel 1 (Minimum) (A), charge Channel 1 (Ah)
msight:ct310:2updatedNew points: current Channel 1 (Maximum) (A), current Channel 1 (Minimum) (A), charge Channel 1 (Ah)
msight:cth01-compress:1updatedNew points: voltageUnbalance (%), rmsVoltage Phase 1 (V), rmsVoltage Phase 2 (V), rmsVoltage Phase 3 (V)
msight:cth01:1updatedNew points: voltageUnbalance (%), rmsVoltage Phase 1 (V), rmsVoltage Phase 2 (V), rmsVoltage Phase 3 (V)
msight:em320-th:1updatedNew points: temperature (Cel), humidity (%RH)
msight:em500-smtc:1updatedNew points: conductivity (uS/cm)
msight:gs524n:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
msight:gs601:1updatedNew points: index Vaping (index)
msight:gs601:2updatedNew points: index Vaping (index)
msight:uc300:1updatedNew points: voltage Analog input 1 (V), voltage Analog input 2 (V)
msight:uc3xxx:1updatedNew points: status Digital input (state), status Digital output (state)
msight:uc511:1updatedNew points: counter Valve 1 pulses (count)
msight:uc512:1updatedNew points: counter Valve 1 pulses (count)
msight:ws52x:1updatedNew points: status Power outage (state)
msight:wt211:1updatedNew points: temperature (Cel)
msight:wt304:1updatedNew points: percentage Valve (%)
msight:wt304:2updatedNew points: percentage Valve (%)
msight:wt401:1updatedNew points: batteryLevel (%), humidity (%RH)

netvox​

DriverChangeWhat changed
netvox:lorawan:1updatedNew points: status Contact (state), presence (state), pm1 (ug/m3), pm2_5 (ug/m3), pm10 (ug/m3), density Particles > 0.3 um (#/cm3), density Particles > 0.5 um (#/cm3), density Particles > 1.0 um (#/cm3), and 29 more

nexelec​

DriverChangeWhat changed
nexelec:air-plus:1updatedNew points: status CO alarm (state)
nexelec:generic2:1updatedPeriodic frames now yield points: the label test read "Periodic data" while the decoder emits "Periodic Data"
nexelec:generic2:2addedNexelec generic2 v2: WAVE product byte 0xAC decoded as "Wave LoRa"; periodic frames and zero values now yield points
nexelec:generic3:1updatedNew points: status Smoke alarm (state)
nexelec:insafe-origin:1updatedNew points: status Smoke alarm (state)
nexelec:track-plus:1updatedNew points: co2Level (ppm), density PM0.5 (#/cm3), density PM1 (#/cm3), density PM2.5 (#/cm3), density PM5 (#/cm3), density PM10 (#/cm3)
nexelec:x2:1updatedProduct Configuration: periodWithoutMotion read from bit 155 (6 bits) per Nexelec guide D1016A, was half the value

nke​

DriverChangeWhat changed
nke:bob:1updatedNew points: frequency (hertz), percentage Anomaly (%), percentage Operating time (%)
nke:zcl:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

pmx​

DriverChangeWhat changed
pmx:pmx-tcr-protocol:1updatedNew points: counter Unfiltered left to right (count), speed Unfiltered left to right (Average) (km/h), counter Unfiltered right to left (count), speed Unfiltered right to left (Average) (km/h), counter Category 1 left to right (count), speed Category 1 left to right (Average) (km/h), counter Category 1 right to left (count), speed Category 1 right to left (Average) (km/h), and 12 more

polysense​

DriverChangeWhat changed
polysen:generic:1updatedNew points: counter Leak (count), leak (state)

quandify​

DriverChangeWhat changed
quandify:cubicmeter-1-1:1updatedNew points: batteryVoltage Recovered (mV), leak (state)

sensaio​

DriverChangeWhat changed
sensaio:generic:1updatedNew points: temperature Internal (K), percentage (%)

sensative​

DriverChangeWhat changed
sensativ:square-air:1updatedNew points: index Air quality (index), tvocLevel Breath VOC equivalent (ppm)
sensativ:strips:1updatedNew points: status Close proximity (state)

sensor-networks-inc​

DriverChangeWhat changed
actility:micropims:1updatedNew points: distance Wall thickness (mm), batteryLevel (%)

socomec​

DriverChangeWhat changed
socomec:diris-b-10l:1updatedNew points: counter (count), status Input 1 (state), status Input 2 (state), status Input 3 (state), status Input 4 (state), status Input 5 (state), status Input 6 (state), status Input 7 (state), and 6 more

tct​

DriverChangeWhat changed
tct:e-green-sensor:1addedTCT e-green sensor driver: current, supercapacitor voltage and thermocouple temperature with history, alerts, errors and configuration acknowledgments

tektelic​

DriverChangeWhat changed
tektelic:agro:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
tektelic:t0008781-stork:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

terabee​

DriverChangeWhat changed
terabee:pc-l-xl:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
terabee:tb-pcm:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

thermokon​

DriverChangeWhat changed
thrmkn:cubicmeter:1updatedNew points: leak (state)
thrmkn:generic:1updatedNew points: status Contact 0 (state), counter Contact 0 (count), presence Occupancy 0 (state), status Contact 1 (state), counter Occupancy 0 (count), counter Contact 1 (count), illuminance (lx)
thrmkn:joylrw:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
thrmkn:sab07:1updatedNew points: status Open window (state), percentage Valve (%)

theta​

DriverChangeWhat changed
theta:dc-series:1addedTheta DC-series ultrasonic corrosion sensor driver (vendor contribution, PR 287): wall thickness, temperatures and battery voltage points

twtg​

DriverChangeWhat changed
twtg:neon-tt:2updatedNew points: batteryVoltage Under load (V), batteryVoltage At rest (V), temperature Device (Minimum) (Cel), temperature Device (Maximum) (Cel)
twtg:neon-tt:3updatedNew points: batteryVoltage Under load (V), batteryVoltage At rest (V), temperature Device (Minimum) (Cel), temperature Device (Maximum) (Cel)
twtg:neon-vb:2updatedNew points: temperature Minimum (Cel), temperature Maximum (Cel), velocity Minimum (X axis) (mm/s), velocity Maximum (X axis) (mm/s), velocity Minimum (Y axis) (mm/s), velocity Maximum (Y axis) (mm/s), velocity Minimum (Z axis) (mm/s), velocity Maximum (Z axis) (mm/s), and 5 more
twtg:neon-vb:3updatedNew points: temperature Minimum (Cel), temperature Maximum (Cel), velocity Minimum (X axis) (mm/s), velocity Maximum (X axis) (mm/s), velocity Minimum (Y axis) (mm/s), velocity Maximum (Y axis) (mm/s), velocity Minimum (Z axis) (mm/s), velocity Maximum (Z axis) (mm/s), and 5 more
twtg:neon-vb:4updatedNew points: charge Transmitter used (mAh), charge Sensor used (mAh), batteryLevel (%)
twtg:ts:2updatedNew points: batteryVoltage Under load (V), batteryVoltage At rest (V)
twtg:vs-qt:2updatedNew points: angle (deg)

volley-boast​

DriverChangeWhat changed
vobo:generic:2updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)

vutility​

DriverChangeWhat changed
vutility:hotdrop-direct:1updatedNew points: charge (Ah), current Average (A), current Maximum (A), current Minimum (A)

watteco​

DriverChangeWhat changed
watteco:atmo:4updatedNew points: status Input (state), counter Number of pulse detection on input 1 (count)
watteco:closo:4updatedNew points: counter Number of pulse detection on input 1 (count)
watteco:closo:5updatedNew points: status Open case detection state (state)
watteco:flasho:4updatedNew points: status Input (state)
watteco:ino:4updatedNew points: counter Number of pulse detection on input 1 (count)
watteco:modbus:4updatedNew points: batteryVoltage (V)
watteco:presso:4updatedNew points: status Input (state), counter Number of pulse detection on input 1 (count), voltage Volt value from 0_10_V input (mV), current amp value from 4_20mA input (mA), batteryVoltage (V)
watteco:smart-plug:4updatedActive energies were published as powerRate in W/h: now energy in Wh
watteco:smart-plug:5updatedActive energies were published as powerRate in W/h: now energy in Wh
watteco:th:4updatedNew points: counter Number of pulse detection on input 1 (count)
watteco:ticso:4updatedNew points: energy EAST (Wh), energy EAIT (Wh), energy BASE (Wh), energy EAP_s (kWh), energy EAP_i (kWh)
watteco:ticso:5updatedNew points: energy EAST (Wh), energy EAIT (Wh), energy BASE (Wh), energy EAP_s (kWh), energy EAP_i (kWh), energy EApP (kWh), energy EApHCE (kWh), energy EApHCH (kWh), and 5 more
watteco:triphaso:4updatedNew points: status Input (state), counter Number of pulse detection on input 1 (count), energy Positive active energy abc (Wh), powerRate Negative active energy (W/h), reactiveEnergy Positive reactive energy (VArh), reactiveEnergy Negative reactive energy (VArh), activePower Positive active power (W), activePower Negative active power (W), and 2 more
watteco:triphaso:5updatedActive energies were published as powerRate in W/h: now energy in Wh; stale example point indexes realigned with the code
watteco:vaqao-lt:4updatedNew points: tvocLevel (ppb)
watteco:vaqao-plus:4updatedNew points: presence (state), tvocLevel (ppb)
watteco:vaqao:4updatedNew points: tvocLevel (ppb)
watteco:ventilo:4updatedNew points: status Input (state), counter Number of pulse detection on input 1 (count)

wavetrend​

DriverChangeWhat changed
wavetrnd:sd01-l:1updatedNew points: counter (count)

yobiiq​

DriverChangeWhat changed
yobiiq:em2101:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
yobiiq:em4301:1updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
yobiiq:iq-rm200-lrw:2updatedextractPoints completed with the physical measurements of the decoder (no example exercises the new points)
yobiiq:sd-1001:1updatedNew points: status Smoke alarm (state), status Interconnect alarm (state)

yosensi​

DriverChangeWhat changed
yosensi:generic:1updatedNew points: status (state), counter (count), energy (kWh)

yz-systems​

DriverChangeWhat changed
yzsyst:aircom:1updatedNew points: status Digital input 1 (state), status Digital input 2 (state), status Digital input 3 (state), status Digital input 4 (state)

zenner​

DriverChangeWhat changed
zenner:co2-ind-ID-A:1updatedDate/time year read from the right bits (EN 13757-3 type F): it was wrong from August to December and for years ending in 4 to 7 after 2000 modulo 8
zenner:easyprotectradio:1addedZENNER EASY PROTECT Radio smoke detector driver with smoke, removal, obstruction, horn and battery alarm points
zenner:edc-module:1addedZENNER EDC B.One module driver (SP0-SP4, SP9, SP12, AP1, AP2) with volume, leak and alarm points
zenner:iuws-module:1addedZENNER IUWS B.One water meter driver with volume and status summary points
zenner:minomess-a-b-one:1updatedDate year decoded 4 years too high from August to December (year mask 0xF0 instead of 0x78)
zenner:pdc-pulse:1addedZENNER PDC B.One pulse module driver, one or two channels
zenner:srmiu:1updatedNew points: counter (count)
zenner:zelsius-c5-cmf:1updatedDate year decoded 4 years too high from August to December (year mask 0xF0 instead of 0x78)

Device profiles​

advantech​

ModelChangeWhat changed
advantec:wise-2200:1updatedClass C device profiles added (RFGroup1/2/4, LoRaWAN 1.0.2); labels gain " - class A" / " - class C"

b-meters​

ModelChangeWhat changed
b-meters:iwm-lr5:1addedB Meters IWM-LR5 LoRaWAN water meter module (LoRaWAN 1.0.4 class A, EU868)

birdz​

ModelChangeWhat changed
birdz:api-vanne:10updateddevice profile label "API VANNE" becomes "API Vanne"
birdz:apilinkv2:20updateddevice profile label "APILINKV2 (version 2.0)" becomes "API Link (version 2.0)"
birdz:bridgev1-0:10updateddevice profile label "BRIDGEV1.0" becomes "Bridge"
birdz:bridgev1-5:15updateddevice profile label "BRIDGEV1.5" becomes "Bridge (version 1.5)"
birdz:bridgev2-0:20updateddevice profile label "BRIDGEV2.0 (version 2.0)" becomes "Bridge (version 2.0)"
birdz:bridgev2-1:21updateddevice profile label "BRIDGEV2.1 (version 2.1)" becomes "Bridge (version 2.1)"
birdz:bridgev2-3:23updateddevice profile label "BRIDGEV2.3 (version 2.3)" becomes "Bridge (version 2.3)"
birdz:bridgev2-4:24updateddevice profile label "BRIDGEV2.4 (version 2.4)" becomes "Bridge (version 2.4)"
birdz:btoolz:1updateddevice profile label "BTOOLZ" becomes "BToolz"
birdz:custom-customg3r:1updateddevice profile label "Z - CUSTOMG3RX2DR1" becomes "Z - Custom G3 RX2 DR1"
birdz:custom-customsf1:1updateddevice profile label "Z - CUSTOMSF11SF12" becomes "Z - Custom SF11 SF12"
birdz:deporte-g3v1:10updateddevice profile label "DEPORTE G3V1" becomes "Déporté G3"
birdz:deporte-g3v2:20updateddevice profile label "DEPORTE G3V2 (version 2.0)" becomes "Déporté G3 (version 2.0)"
birdz:deporte-sm4-3:10updateddevice profile label "DEPORTE SM4.3" becomes "Déporté SM4.3"
birdz:fillink:10updateddevice profile label "FILLINK" becomes "Fillink"
birdz:g3v1:10updateddevice profile label "G3V1" becomes "G3"
birdz:g3v2-ja-delay-15:20updateddevice profile label "G3V2_JA_DELAY_15MS (version 2.0)" becomes "G3 JA delay 15 ms (version 2.0)"
birdz:g3v2:20updateddevice profile label "G3V2 (version 2.0)" becomes "G3 (version 2.0)"
birdz:g3v3:30updateddevice profile label "G3V3 (version 3.0)" becomes "G3 (version 3.0)"
birdz:g3v4:50updateddevice profile label "G3V4 (version 5.0)" becomes "G3 (version 4.0)", product version corrected from 5.0 to 4.0
birdz:g3v5:50updateddevice profile label "G3V5 (version 5.0)" becomes "G3 (version 5.0)"
birdz:luka:10updateddevice profile label "LUKA" becomes "Luka"
birdz:minotaure-c:10updateddevice profile label "MINOTAURE_C" becomes "Minotaure C"
birdz:minotaure-vt:10updateddevice profile label "MINOTAURE_VT" becomes "Minotaure VT"
birdz:relay:10updateddevice profile label "RELAY" becomes "Relay"
birdz:sewerin:10updateddevice profile label "SEWERIN" becomes "Sewerin"

decentlab​

ModelChangeWhat changed
dl:dl-atm41g2:1addedDecentLab DL-ATM41G2 weather station (2nd generation)
dl:dl-blg:1addedDecentLab DL-BLG model
dl:dl-ctd10b:1addedDecentLab DL-CTD10B model
dl:dl-cws:1addedDecentLab DL-CWS model
dl:dl-cws2:1addedDecentLab DL-CWS2 model
dl:dl-dlr2-009:1addedDecentLab DL-DLR2-009 PT1000 model (no driver yet)
dl:dl-dlr2-011:1addedDecentLab DL-DLR2-011 dual dry-contact input model
dl:dl-isf:1addedDecentLab DL-ISF model
dl:dl-lws:1addedDecentLab DL-LWS model
dl:dl-mes5:1addedDecentLab DL-MES5 model
dl:dl-ntu:1addedDecentLab DL-NTU model
dl:dl-pheht:1addedDecentLab DL-PHEHT model
dl:dl-sdd:1addedDecentLab DL-SDD model

dragino​

ModelChangeWhat changed
dragino:laq4:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lht65:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:llms01:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lsn50-v2:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lsn50v2-d20-d22:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lsn50v2-d20:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lsph01:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lt22222-l:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:lt33222-l:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices
dragino:ltc2:2updatedDragino manufacturer driver added first; the os1-drag driver stays for deployed devices

ezurio​

ModelChangeWhat changed
ezurio:rs1xx-1w:1addedSentrius RS1xx duplicated from laird:ext-temp-1w:1 under the Ezurio brand (laird model kept for deployed devices)
ezurio:rs1xx-ms:1addedSentrius RS1xx duplicated from laird:ext-multi:1 under the Ezurio brand (laird model kept for deployed devices)
ezurio:rs1xx-rtd:1addedSentrius RS1xx duplicated from laird:ext-temp-rtd:1 under the Ezurio brand (laird model kept for deployed devices)
ezurio:rs1xx-trh:1addedSentrius RS1xx duplicated from laird:temp-rh:1 under the Ezurio brand (laird model kept for deployed devices)
ezurio:rs261-ext:1addedNew vendor Ezurio: Sentrius RS261 (EU/UK) with external temperature probe
ezurio:rs261-int:1addedNew vendor Ezurio: Sentrius RS261 (EU/UK) with internal temperature sensor
ezurio:rs262-ext:1addedNew vendor Ezurio: Sentrius RS262 (US/AU/NZ) with external temperature probe
ezurio:rs262-int:1addedNew vendor Ezurio: Sentrius RS262 (US/AU/NZ) with internal temperature sensor

milesight-iot​

ModelChangeWhat changed
msight:em300-di:1updatedModel name typo fixed: "EM300-DI Pusle counter" becomes "EM300-DI Pulse counter"

nexelec​

ModelChangeWhat changed
nexelec:feel:1updatednexelec:generic2:2 added as the default driver, v1 kept for deployed devices
nexelec:move:1updatednexelec:generic2:2 added as the default driver, v1 kept for deployed devices
nexelec:rise:1updatednexelec:generic2:2 added as the default driver, v1 kept for deployed devices
nexelec:sign:1updatednexelec:generic2:2 added as the default driver, v1 kept for deployed devices
nexelec:wave:1addedNexelec WAVE (X530) model on nexelec:generic2:2

pf​

ModelChangeWhat changed
pf:ws-val-2n:1updatedWilsen valve/node model description written from the datasheet
pf:ws-val-2n4:1updatedWilsen valve/node model description written from the datasheet
pf:ws-val-2zl:1updatedWilsen valve/node model description written from the datasheet
pf:ws-val-4zl:1updatedWilsen valve/node model description written from the datasheet
pf:wsn-2n:1updatedWilsen valve/node model description written from the datasheet
pf:wsn-2zl:1updatedWilsen valve/node model description written from the datasheet

tct​

ModelChangeWhat changed
tct:e-green-sensor:1addedNew vendor TCT and model e-green sensor (self-powered clip-on current sensor), EU868 LoRaWAN 1.0.4 class A

theta​

ModelChangeWhat changed
theta:dc110-l:1addedNew vendor Theta Sensors and model DC110-L ultrasonic corrosion monitoring sensor, US915 LoRaWAN 1.0.3 class A

zenner​

ModelChangeWhat changed
zenner:easyprotectradio:1addedZENNER EASY PROTECT Radio smoke detector
zenner:edc-b-one:1addedZENNER EDC B.One communication module for water meters
zenner:iuws-b-one:1addedZENNER IUWS B.One ultrasonic water meter
zenner:pdc-b-one:1addedZENNER PDC B.One pulse module

Across the catalog​

CatalogWhat changed
devicesevery device model states whether it can be exposed through the BACnet and Modbus gateways — Each model.yaml carries supportedBACnetModbus: true for the 279 of 1155 models whose driver ships a BACnet/Modbus mapping. The supported devices page shows it in its BACnet Modbus column.
Last updated on