Skip to main content
Version: AT2 v2.3

Configuration messages

This message reports the parameter values configured in the trackers. If the complete list is requested, several UL messages will be transmitted.

Common headerDataDataDataDataDataData
Byte 0-4Byte 5Byte 6-10Byte 11-15Byte 16-20Byte 21-25Byte 26-30
Header with Type=0x070x02Parameter 1Parameter 2Parameter 3Parameter 4Parameter 5

Parameter x: Configuration of the parameter x, encoded on 5 bytes as follow:

Parameter xParameter x*
Byte (5*x+1)Byte (5*x+2) - (5*x+5)
Parameter IDParameter value

Parameter ID:

ParameterIDParameterIDParameterID
ul_period0x00reed_switch_configuration0x29position_ble_report_type0x52
lora_period0x01gnss_constellation0x2Abuzzer_volume0x53
pw_stat_period0x02prox_scan_pwr_min0x2Bangle_detect_mode0x54
periodic_pos_period0x03prox_distance_coef0x2Cangle_ref_acq0x55
Reserved, do not use0x04prox_scan_frequency0x2Dangle_ref_acc_x0x56
geoloc_sensor0x05prox_backtrace_max_age0x2Eangle_ref_acc_y0x57
geoloc_method0x06prox_distance_sliding_window0x2Fangle_ref_acc_z0x58
Reserved, do not use0x07prox_exposure_500x30angle_critical0x59
motion_nb_pos0x08prox_exposure_1000x31angle_critical_hyst0x5A
gps_timeout0x09prox_exposure_1500x32angle_report_mode0x5B
agps_timeout0x0Aprox_exposure_2000x33angle_report_period0x5C
gps_ehpe0x0Bprox_exposure_2500x34angle_report_repeat0x5D
gps_convergence0x0Cprox_exposure_3000x35angle_rising_time0x5E
config_flags0x0Dprox_exposure_4000x36angle_falling_time0x5F
transmit_strat0x0Eprox_alarm_dist_immediate0x37angle_learning_time0x60
ble_beacon_cnt0x0Fprox_alarm_exposure0x38angle_acc_accuracy0x61
ble_beacon_timeout0x10prox_warn_dist_immediate0x39angle_deviation_delta0x62
gps_standby_timeout0x11prox_warn_exposure0x3Aangle_deviation_min_interval0x63
confirmed_ul_bitmap0x12prox_record_dist_immediate0x3Bangle_deviation_max_interval0x64
confirmed_ul_retry0x13prox_record_exposure0x3Cdefault_profile0x65
motion_sensitivity0x14prox_alarm_buz_duration0x3Dpassword0x66
shock_detection0x15prox_warn_buz_duration0x3Egps_t0_timeout0x67
periodic_activity_period0x16prox_contact_policy0x3Fgps_fix_timeout0x68
motion_duration0x17prox_scan_duration0x40geofencing_scan_duration0x69
geofencing_scan_period0x18prox_scan_window0x41beaconing_type0x6A
geofencing_collect_period0x19prox_scan_interval0x42beaconing_tx_power0x6B
ble_rssi_filter0x1Aprox_alarm_remanence0x43beaconing_static_interval0x6C
temperature_high0x1Bprox_warn_remanence0x44beaconing_motion_interval0x6D
temperature_low0x1Cprox_bcn_repeat0x45beaconing_motion_duration0x6E
temperature_action0x1Dprox_bcn_tx_power0x46ble_cnx_adv_duration0x6F
transmit_strat_custom0x1Eprox_reminder_period0x47beacon_id_00x70
network_timeout_check0x1Fprox_reminder_distance0x48beacon_id_10x71
network_timeout_reset0x20prox_warn_disable_dist0x49beacon_id_20x72
collection_scan_type0x21prox_alarm_disable_dist0x4Abeacon_id_30x73
collection_nb_entry0x22prox_max_speed_filter0x4Bbeacon_id_40x74
collection_ble_filter_type0x23prox_max_update0x4Csos_period0x75
collection_ble_filter_main_10x24position_ble_filter_type0x4Dmotion_debounce0x76
collection_ble_filter_main_20x25position_ble_filter_main_10x4Ebutton mapping0x77
collection_ble_filter_sec_value0x26position_ble_filter_main_20x4Fdefault_datarate0x78
collection_ble_filter_sec_mask0x27position_ble_filter_sec_value0x50
battery_capacity0x28position_ble_filter_sec_mask0x51
Note

Parameters in bold are new or modified in this firmware version.

Parameter value: Unsigned 32 bits value in big endian format (MSB first).

Special parameters

Firmware version (Parameter ID equals to 0xFD or 0xFE) should be read as follows:

Parameter xParameter IDParameter value
Byte 5*x+10xFD or 0xFE
Byte 5*x+20x00
Byte 5*x+3Firmware version
Byte 5*x+4Firmware revision
Byte 5*x+5Firmware iteration

Example

Parameter=0xfe00010881, Firmware version=0x01, Firmware revision=0x08, Firmware iteration= 0x81

  • Tracker orientation (Parameters ID equals to 0xFA, 0xFB or 0xFC) can be negative. Refer to the section Two's complement Encoding for information for the encoding.
Parameter xParameter IDParameter value
Byte 5*x+10xFA, 0xFB or 0xFC
Byte 5*x+2 - 5*x+5X, Y or Z Axis

X, Y or Z Axis: Value measured on axis X, Y or Z of the accelerometer, it is expressed in mG. Refer to the section Two's complement Encoding for information for the encoding

  • Operational Mode (Parameter ID equals to 0xF9): Unsigned 32 bits value in big endian format (MSB first).

    • 0- Standby
    • 1- Motion tracking
    • 2- Permanent tracking
    • 3- Motion start/end tracking
    • 4- Activity tracking
  • Dynamic profile configuration (Parameter ID equals to 0xF6): provides the dynamic profile of the tracker.

    • 0: No profile
    • 1: Profile sleep
    • 2: Profile economic
    • 3: Profile intensive
  • Power consumption (Parameter ID equals to 0xF7): provides the power consumption of the tracker in mA

  • BLE Bond status (Parameter ID equals to 0xF8): Unsigned 32 bits value in big endian format (MSB first).

    • 0: the tracker is not bonded
    • 1: the tracker is bonded
    • 2: unknown state